RSH -1151/1651
1817
15. MAINTENANCE 17. SPECIFICATIONS
16. TROUBLESHOOTING
Cleaning the Body of the laminaor
1. To clean the machine body, dampen a cloth with water only and gently wipe the machine clean.
Removing Adhesive Build Up
1. Remove the film from the laminator.
2. Use a damp (water only) cloth and a rubber gum eraser to remove the adhesive on the
silicone rollers.
Note: Rub firmly but do not scrub the rollers vigorously as this may scratch the
surface.Do not use sharp metal objects, steel wool, or abrasives, as these
may also damage the rollers.
Problem Cause Solution
Machine will not turn
on:
a. Power plug is not plugged in.
b. Power switch is in “0” (Off) position.
c. Tripped circuit breaker.
d. Blown main power fuse.
a. Plug the power cord into appropriate
outlet.
b. Put the power switch to the “I” (On)
position.
c. Reset the circuit breaker.
d. Replace the fuse.
There is power, but the
rollers are not turning
after the “RUN” button
is pressed:
a. Emergency switch (es) is (are)
engaged.
b. Safety cover is not closed.
c. Paper guide is not installed correctly.
d. Blown motor fuse.
a. Disengage the emergency switch (es).
b. Close the safety cover to active the
safety switch.
c. Properly install the paper guide so that
the micro switch is activated.
d. Replace the motor fuse.
The unit is not heating
up:
a. The machine is in “COLD” mode.
b. Set temperature is lower than the room
temperature.
a. Switch to “HOT” mode.
b. Raise the temperature according to the
recommended film temperature.
Curled lamination:
a. Upward curl.
b. Downward curl.
a. Loosen the top roll film tension.
b. Loosen the bottom roll film tension.
Unclear lamination:
a. The main roller temperatures are too
low and/or lamination speed is too fast.
a. Raise the roller temperatures and/or
lower the lamination speed.
RSH-1151
AC 200,220~240V
50/60Hz
3300W
1150mm / 45"
25 ~ 250mic / 1~10mil
Hot : 3 m/min / 9.8 ft/min
Cold : 4 m/min / 13.1 ft/min
20 min
Hot roller
DC geared
160°C / 320°F
9 settings
4 Roller
Auto grip (2.25", 3")
2 Blower
No
Yes
No
Yes
Yes
15mm / 0.6"
chain link to main motor
Option
Option
Yes
Yes
Yes
1500 x 650 x 1210 (mm)
59" x 25.5" x 47.5"
169kg / 373lbs
1660 x 900 x 1460 (mm)
65.5" x 35.5" x 57.5"
280kg / 618lbs
RSH-1651
AC 200,220~240V
50/60Hz
3300W
1650mm / 65"
25 ~ 250mic / 1~10mil
Hot : 3 m/min / 9.8 ft/min
Cold : 4 m/min / 13.1 ft/min
40 min
Hot roller
DC geared
160°C / 320°F
9 settings
4 Roller
Auto grip (2.25", 3")
3 Blower
No
Yes
No
Yes
Yes
15mm / 0.6"
chain link to main motor
Option
Option
Yes
Yes
Yes
1960 x 650 x 1210 (mm)
77" x 25.5" x 47.5"
269kg / 593lbs
2190 x 900 x 1460 (mm)
86" x 35.5" x 57.5"
394kg / 869lbs
Description
Power supply
Power consumption
Max laminating width
Film thickness
Max laminating speed
Ready time
Heating method
Driving motor
Max. temperature control
Speed control
Transport type
Film core size
Cooling system
Side cutter
Cross cutter
Film alignment
Hot lamination
Cold lamination
Mounting thickness
Take up system
Paper counter
Length measurement
Reverse
Remote control
Foot pedal
Unit dimensions
(w x d x h)
Unit weight
Carton dimensions
(w x d x h)
Carton weight
(12 pages)
(24 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals